how close does tongue and groove deck fit

Joining Tongue-and-Groove Plywood | This Old Housetongue-and-groove plywood is superior to regular plywood for floor decks because it creates a stronger, more rigid subfloor, and helps eliminate sagging and "bounce" at the seams between the joists. But it is also more difficult to install because the tight-fitting joints don't always go together easily. Here's a simple way to close up those joints: Lay a 4-foot-long 2x4 across the joists to protect the plywood edge. Stand on top of the 2x4, then gently rap it with a sledgehammer.

How to Install a Tongue-and-Groove Plank Ceiling | how-tos | DIYInstall Planks. Start with your first piece: groove facing the wall, tongue facing out. Use the framing gun to add a nail to the tongue of the plank and secure in place. For the next piece, you will connect the groove of the new piece into the tongue of the first piece.

Tigerwood Deck Installation - Advantage LumberTigerwood deck Installation. Follow these directions for perfect results. tigerwood deck install ... This page will give you an overview of handling and building suggestions that will help you achieve excellent results when building your deck. Click HERE to go to our ... patios only. Installing tongue and groove on a deck without a roof covering the deck surface will cause problems such as allowing excessive water to collect and cause the material to cup, swell, and buckle.

How to Install a V-Groove Pine Ceiling - Wood, Naturally14 Dec 2017 ... does the roof have any leaks? Which way do you want to run the V-groove? DSC04979. To start, the porch framing should be solid and in good shape. The joists should be no more than 24 on center. If they are, then you will need to screw 1×2 strapping in a 12 ... In order to seat each successive row, cut grooved blocks so hammering against the tongue doesn't damage the wood. DSC05029 ... Using 15 gauge nails, install the trim around the perimeter of the ceiling.

How to properly install tongue and groove plywood subfloor? - Home ...Do not drop the plywood on the glue or set the plywood off the final placement too far or firstly the glue will splatter all out off of the joist, or slide or scrape the glue off the joists. I seen both of these things happen in my years of construction. Needless to say the bond will not be worthy. The tongue or the groove does not need to be glued, although there is no reason not to. Some engineers require it in certain applications, but for standard subfloor applications none will ...

PTG FLOORING: Tongue and Groove flooring - Metsä WoodAt Metsä Wood we offer a range of high quality softwood Planed tongue and groove (PTG) flooring available in various sizes. Our softwood PTG flooring ... As timber is a natur

How to Install a Tongue and Groove Ceiling | Family HandymanIf you're installing T&G over drywall (or plaster especially), it's a good idea to install 1×2 battens and fasten them directly to the framing with 2-1/2-in. screws. They'll give you a much more solid nailing surface. If you try to nail through the T&G and the drywall, you can't be sure the nail will penetrate far enough to securely hold. Also, the battens will somewhat flatten out uneven ceilings. Another plus: You can run the battens either parallel or perpendicular to the ceiling framing, ...

How to Install Tongue & Groove Mahogany Decking | Home Guides ...Although installing mahogany tongue-and-groove decking boards is similar to installing interior flooring boards, there are some key differences. You probably won't have a ... It's important to provide a moisture barrier under the flooring to prevent warping, but even if you do, rain and sun will probably still cause some warping. You can minimize this with a ... 3/4 inches of its end. To prevent the wood from splitting, drill pilot holes for the screws near the ends, using a 3/16-inch drill bit.

Lesson: Shiplap, Tongue & Groove: the paneling discussion ...On the other hand, tongue and groove boards are cut so that the tongue of one piece fits into the groove of the adjacent piece in an interlocking method. Advantages of tongue and groove (exterior) tongue and groove siding fits together to do a better job of keeping the elements out of the house than shiplap. This enables the workman to install the siding in either a vertical or horizontal manner, though horizontal is more common. tongue and groove siding tends to lay flatter against ...